首页

宣城行业资讯

当前位置: 首页>>新闻中心>>宣城行业资讯

宣城流水线:汽车车身内饰板链输送及装配线

宣城装配生产线,宣城输送流水线:车身内饰板链输送及装配线 :车身装配输送线采用板式链输送机,张紧装臵和驱动装臵分别设臵在线体前后端、宽板式输送链上每工位长度4.5m,设臵有16个车位,线长约75m。


宣城流水线:车身内饰板链输送及装配线 :链板采用优质花纹钢板,钢板厚6毫米,对所有的面板用筋板进行加强。


宣城流水线:车身内饰板链输送及装配线 :链板长2m宽200mm,链速0.5m/min-2m/min。

宣城输送流水线:车身内饰板链输送及装配线 :电气控制系统分为1套PLC控制。


宣城流水线:车身内饰板链输送及装配线 :线体速度可以通过设备管理计算机系统进行设定。


为提高宣城流水线:车身内饰板链输送及装配线 的可靠性,输送系统的单元设备电机减速机采用SEW电机。


宣城流水线:车身内饰板链输送及装配线 运行速度0.5m/min-2m/min  


宣城装配生产线:车身内饰板链输送及装配线 变频调速.


宣城流水线:车身内饰板链输送及装配线 链条其结构为可拆式,内外板片厚度满足其抗拉强度要求,链片厚不低于8MM,其材质为16Mn,轴销为40Cr钢并经调质处理,滚轮表面硬度不小于HRC38,链条滚轮内安装轴承可降低运行阻力,避免爬行,且轴承内加润滑脂:由专业厂家宣城竞流按行业标准制造,质量保证;销轴、滚轮均经热处理工序,链条链片表面须经抛丸防锈处理 


Assembly production line, conveying line: body interior trim plate chain conveying and assembly line: body assembly conveying line adopts plate chain conveyor, tensioning device and driving device are respectively set up on the front and rear ends of the line body, and the length of each station on the wide plate conveyor chain 4.5m, there are 16 parking spaces, and the line is about 75m long.




Assembly line: chain conveyor and assembly line for car body interior trim panels: chain plates are made of high-quality checkered steel plates with a thickness of 6 mm, and all panels are reinforced with ribs.




Assembly line: car body interior trim plate chain conveyor and assembly line: chain plate length is 2m wide and 200mm, chain speed is 0.5m/min-2m/min.


Conveying line: body interior trim plate chain conveying and assembly line: The electrical control system is divided into 1 set of PLC control.




Assembly line: car body interior trim plate chain conveyor and assembly line: the line speed can be set through the equipment management computer system.




In order to improve the reliability of the assembly line: car body interior trim plate chain conveying and assembly line, the unit equipment motor reducer of the conveying system adopts SEW motor.




Assembly line: car body interior trim plate chain conveyor and assembly line, operating speed 0.5m/min-2m/min




Assembly production line: car body interior trim plate chain conveyor and assembly line frequency conversion speed regulation.




Assembly line: The structure of the car body interior trim plate chain conveyor and assembly line chain is detachable, the thickness of the inner and outer plates meets its tensile strength requirements, the thickness of the chain is not less than 8MM, the material is 16Mn, the shaft pin is 40Cr steel and adjusted Quality treatment, the surface hardness of the roller is not less than HRC38, the bearing installed in the chain roller can reduce the running resistance and avoid crawling, and the bearing is lubricated: manufactured by professional manufacturers according to industry standards, quality assurance; pins and rollers are heat treated In the process, the surface of the chain must be shot blasted and treated for rust prevention



服务区域: 安徽 北京 重庆 江苏 山东 上海 天津 浙江 石家庄 廊坊 沈阳 大连 长春 南京 无锡 徐州 常州 苏州 南通 杭州 合肥 芜湖 福州 厦门 济南 青岛 郑州 武汉 长沙 成都 西安